DMH Low Profile Electric Cutouts - Write Up

[BOS/SRT]

I removed the entire cig lighter assembly, leaving a hole for me to mount the cutout switch, but the hole is bigger than switch. I couldn't find a plastic adapter, fortunately I tried "power brake check grommet and it fit perfectly and the switch is secure. Here's the pic of grommet...
http://i166.photobucket.com/albums/u99/BosChargerSRT/c3acf4ce.jpg
Here's the ash tray switch..
http://i166.photobucket.com/albums/u99/BosChargerSRT/521dd33a.jpg
I will post more pix of install and unit later tonight. I will also be running the wiring through the firewall grommet into the bay and wrap it up secure, so it will be ready once they weld the cutouts.

[BOS/SRT]

I apologize, because i didn't take many pictures of install. I didn't think it was necessary, because there are already plenty of threads on this mod. I just did it a little differently. Most tap into the cig lighter, i just replaced it with the cutout switch, which i then ran the line under lower dash panel, beneath the steering wheel. Zipped it to the only rubber grommet i could find leading out into the engine bay, then bunched the lines up and zipped it. I tucked it up around the wiper blade motor untill the cutouts could be welded on.
here's the few pics of have of the interior and grommet area to run the line out from.
cig lighter assembly removed:
http://i166.photobucket.com/albums/u99/BosChargerSRT/deb7f45f.jpg
cutout switch:
http://i166.photobucket.com/albums/u99/BosChargerSRT/53311749.jpg
under the drivers dash, grommet opening: not necessary to remove lower dash panel to get to it.
http://i166.photobucket.com/albums/u99/BosChargerSRT/DSCN2674.jpg
engine bay opening:
http://i166.photobucket.com/albums/u99/BosChargerSRT/DSCN2675.jpg

[BOS/SRT]

mounting plate received wasn't fully welded and one the adapter was slanted, which means would cause a bad seal and leak.
mounting plates:
http://i166.photobucket.com/albums/u99/BosChargerSRT/76b5566e.jpg
http://i166.photobucket.com/albums/u99/BosChargerSRT/84643729.jpg
Lou's fixed both issues and did an awesome job running the two wires to the cutouts. gotta admit, better than i expected and something i didn't think about.
drivers side:
http://i166.photobucket.com/albums/u99/BosChargerSRT/fb47c172.jpg
http://i166.photobucket.com/albums/u99/BosChargerSRT/c3845e5f.jpg
pax side:
http://i166.photobucket.com/albums/u99/BosChargerSRT/4b7643af.jpg
http://i166.photobucket.com/albums/u99/BosChargerSRT/01ec985c.jpg
http://i166.photobucket.com/albums/u99/BosChargerSRT/baea2896.jpg

[BOS/SRT]

Here's a vid of cutouts sitting. I will try to get some of drive by soon... btw, video does this mod no justice. It's louder and meaner in person.

http://www.youtube.com/watch?v=1HzDeYS6bXE

[SmokedRam]

damn fine work....looks great

[BAD HABIT]

thats a odd way for dmh to make those i figured they would be a universal like inlines, but i guess not but those look good and sound nicer....

[Fla 66 cuda]

Nice install sounds good thanks.

[BOS/SRT]

unfortunately the owner has a bad rep and i know why...... oddly enough, i haven't really opened them up since installing them. don't know why? oh yeah, there loud as shiat and almost caused an elderly couple to get into an accident at the light. i knew it was an elderly couple, when all i can see are tops of eyes and forehead over the steering wheel. ROFL! I'm not mean. :)

[OklaHemi]

that is bad ass. my daughter loves you car

[NOTPAID4]

Those are awesome; I have a set on my 05 Mag R/T and love them...

[Silverbullet08]

u think its loud now. wait till u go cam and headers. i cant here myself think when its open lol

[BOS/SRT]

Yeah, I'm well aware of the difference once engine performance is added. The more I think about it, the more I realize these wont get much use.

[Fla 66 cuda]

Yea but you know they are there[you know you'll use them ocasonally].I can't wait to do my exhaust on the cuda i'll be playin with mine every friday night prolly get a ticket but well worth it.